How to set up Wi-Fi: step by step guide

A couple of decades ago, a small number of people knew about the existence of the Internet. Now the whole civilized world knows about it, moreover, everyone uses it. The first Internet connected users with a network of wires, which continues today. But technology does not stand still, and wireless data transmission has been developed. In this article, we will learn how to set up WiFi on a Windows laptop of any version.

Why customize and what is it?

If you are reading this article, then you have an understanding of how wireless networks work. However, some users do not fully understand why cloud transmission technology is used.

Wifi was first tested in 1998. It was a primitive technology that did not provide adequate protection, and the signal did not go beyond one small room.

At the moment, wireless technology is used in all homes, offices, schools and so on. It allows users to connectto one access point, while the wires remain in only one place. To do this, you need to know how to configure the distribution of WiFi. This can be handled by an ordinary user, with which we will help him.

Action one. Turning on the router

Before you start working with a wireless network and setting it up, you need to make sure that the router is connected to a common network connected by a wire system. To do this, go to the modem and follow the following algorithm:

1. See if the lights are on, if not, turn them on.
2. Usually, the power button is located on the back panel.
3. Press it once.

If the modem is working, the lights will start to glow in some color that the manufacturer has set (usually green). If for some reason the indicators do not turn on, check the connection of the router to the outlet. Then turn on the device again.

Action two. Checking Wi-Fi on a laptop

As you know, a wireless signal receiver is built into new laptop models. A similar device can be purchased for your computer, it is inexpensive. How to set up a Wi-Fi network? For each laptop, this is individual.

For the Lenovo model, there is no function button that turns on Wi-Fi. As practice shows, the switch is located on the front of the laptop. ASUS stopped checking for Fn+F2 keys, and Acer for Fn+F3. The rest of the hotkeys you can see on the website of the manufacturer of your device.

You can tell if the adapter is turned on by the glow of the lightindicator. It is usually located on the left side of the laptop. But don't be discouraged if you don't have it. In the Windows 10 operating system, the inclusion of the adapter is checked through the panel, which displays the sound, language and other parameters.

My adapter won't turn on, what should I do?

If you are asking this question, don't worry, the problem is most often the lack of necessary software or virus software. The Windows system is imperfect, and there are failures in it, which causes the network adapter to work incorrectly.

Follow these tips:

• Install anti-virus programs. For example, Doctor Web or Avast.
• Reboot your laptop, to do this, go to the "Start" menu and select "Restart".
• If all else fails, take your laptop to a service center.

But don't rush to give away your device, perhaps the next step will help you.

Action three. Driver Installation

They ensure the normal operation of all programs and the Windows operating system. And it is quite obvious that without them we will not be able to learn how to set up the Internet via WiFi.

They are loaded on the official website of the manufacturer or automatically when the device is connected. It is strongly discouraged to use programs that download the necessary drivers. Although they are convenient, they can harm your system.

To force the automatic installation of drivers, you need to runfollowing steps:

1. Go to the start menu.
2. Click on "All Programs".
3. And click on "Command Prompt", be sure to run it as an administrator.

And sequentially enter (one by one) the commands:

• sc config Wlansvc start=auto;
• net start Wlansvc.

After that, your Wi-Fi adapter will recognize the access points and connect to them.

How to set up WiFi in a Tp-Link router?

This is one of the most popular device brands among users, so let's analyze the setting using its example. The manufacturer has achieved maximum optimization of price and quality. However, this is not enough for us, because the modem still needs to be configured, and the following describes how to do this:

1. Connect the router to the mains.
2. Install the cord into the WAN connector.
3. Insert the wires into the appropriate connectors on the computer.

Then the setting comes into play:

1. Press the Reset button on the modem with a needle or other similar object.
2. Hold like this for 10 seconds.

The router will restart and revert to default settings. Then dial any of the following addresses:

• "192.168.0.1",
• "192.168.1.1".

And follow this algorithm:

1. In the "Username" field type admin.
2. Click on "Send".
3. You will open a new window with the Wi-Fi interface. Please update the modem firmware version before proceeding with the rest of the steps.
4. Then enter the System Tool.
5. Register in the system by writing admin in the first two paragraphs.

Direct setup

Now we will learn how to set up WiFi in a Tp-Link router, for this, read the instructions below:

1. Click on Network.
2. Click on WAN.
3. Specify the type of network, it is written in the contract.
4. Save your data.
5. Click on MAC Clone.
6. Click on Clone MAC Address.
7. Click Save.

Now let's deal with the distribution:

1. Open the Wireless section and go to WirelessSettings.
2. Fill in all fields and come up with a name for your Wi-Fi.
3. Click Save.
4. Next, enter Wireless (Wi-Fi) Security.
5. Set the parameters as shown in the screenshot.

Then you should restart the modem, go to System Tools and then to Reboot, where click on Reboot. Once you click, you will be prompted to agree to the restart, click on "OK". After that, it is recommended to turn off and turn on your computer.

Setting for Windows 7, 8 and 10

The algorithm is almost the same, and there is no point in somehow differentiating the description. How to set up WiFi? Description - below:

1. Open the Start menu.
2. Enter the Control Center tab.
3. Then click on "Networks andInternet".
4. And go to "Network and Sharing Center".
5. Then click on "Change adapter settings".
6. Open the "Wireless Properties" tab and set the required parameters.
7. Return to step 4.
8. Click on "Connect to network".
9. Select an available connection and click "Connect".

This setting, as noted, is slightly different. However, the algorithm of most actions is similar, and there is no need to describe individual connection principles.

How do I set up WiFi on my phone?

This is optional, the mobile device connects directly to an existing network. And we only have to enter the password for Wi-Fi or turn on the search to find a wireless connection.

Nothing complicated here, you previously set the password, use it. You only need to turn on the modem and configure it correctly, and for the laymen in mobile technology there is a connection instruction, which is presented below:

1. Open the "Settings" menu.
2. Go to Wi-Fi.
3. From the list of networks choose your own.
4. Enter password and click OK.

Now you know how to set up WiFi on your phone. And as you can see, this is nothing complicated. It is worth noting that a modern smartphone not only receives a signal, but also distributes it.

Connecting Windows XP

Yes, yes, someone is still on the old operating system, and they also want to know how to set up WiFi. And to do this is extremely simple, the algorithm of actions is similar to the setting in new versions.

1. Start the "Start" menu and go to the "Control Panel".
2. Select "Network Connections" and find "Wireless Connection".
3. Right click on it and open "Properties".
4. In the "General" section and in the "Components" column, click on "TCP/IPv4 protocol" and select "Properties".
5. Set the options you need, they depend on your modem.
6. Go to "Wireless &Networks".
7. In the "Available networks" tab, select "Wireless networks".
8. Update the list.
9. Set the desired network and click on "Connect".

No other action is needed, you are now connected to the World Wide Web. If you have password-protected the network, then you will need to enter the key and confirm the actions. In general, update your system to the newer "Windows 10". It is several times easier to work with Wi-Fi settings in it.